42V 350W 15A XT60 Motor Controller+Dashboard+Front/Rear Light for Scooter Electric Bicycle E-bike

Description:
Ultra-quiet, motor torque ripple is minimized to achieve no noise, no vibration and comfortable
operation.Based on the Field Oriented Control (FOC) algorithm, the controller has high conversion efficiency,
which can effectively reduce controller temperature rise and extend battery life.
Specification:
Operating Voltage:Minimum:31V, Typical:35V, Maximum:45V
Low Pressure Stop::Minimum:30.5V, Typical:31V, Maximum:31.5V, Remarks:The last cell flashes red
Motor Current Limit:15±1A
Quiescent Current:30uA
Ambient Temperature:Minimum:-30℃, Typical:35℃, Maximum:80℃
Rated Power:350W
Overvoltage Protection:45V
Stall Protection Delay:2 seconds
Sleep Time:10 minutes
Phase Angle:120°
Output Waveform:Sine wave
Motor matching:8.5 inches 15 pairs of poles Hall motor
Shell Waterproof Rating:Ordinary waterproof
Instrument Matching:PRO meter
Motor Driven:FOC vector algorithm
Shell Size:118mm*48mm*32mm
Housing Material:Aluminum
Features:
1.Power on/off: Short press 0.5 second/power on, long press 2 seconds to shut down。
2.Cycling mode:Non-zero start mode (that is, press the accelerator to start when the sliding speed
reaches 3KM/H); zero start mode (turn the accelerator bar to start the motor in a stationary state).
3.Speed gear: 1 files 10KM/H, 2 files20KM/H, 3 files 25KM/H. Click to switch the gear (with memory
function, the default is the gear used before the last shutdown).
4.Electronic brake: Compatible with power-off brake and linear Hall brake.
5.Taillight:The light is always on and the brake flashes.
6.Constant speed cruise mode: 1.Fixed-speed cruise function turned on:When the accelerator
speed control is stabilized in the riding mode, the cruise mode is automatically entered after 6
seconds. (Press the brake, accelerator, switch gear, you can exit the cruise mode). 2. Fixed-speed
cruise function turned off:No cruise was allowed during the ride.
7.Self-learning: first power on, run at no-load speed and keep the handlebar for 3 seconds, then
release the handlebar for 5 seconds. After the motor drive stops, the motor parameters can be
learned and saved automatically.
8.MOS tube breakdown protection: Before or when the controller is powered on, the D and S poles
of the upper arm or lower arm of a phase MOS tube are short-circuited, the controller stops driving
and has no output. You need to power on again after troubleshooting to work normally
Power Display:
1) Voltage 38.2V-42V The first second third fourth fifth lights are always on
2) Voltage 36.6V-38.2V The first second third fourth light is always on
3) Voltage 34.5V-36.6V The first second third lights are always on
4) Voltage 32.8V-34.5V The first second light is always on
5) Voltage 31.5V-32.8V The first light is always on
6) Voltage 30-31.5V The last grid flashes
7) Turn-off of motor with voltage below 31V
Error Code:
1) ‘E1’ Motor Hall failure
2) ‘E2’ MOS
MOS fault or motor phase line short circuit fault
3) ‘E3’ Brake failure
4) ‘E4’ Handlebar failure
5) ‘E5’ Undervoltage protection
6) ‘E6’ Instrument/control communication failure
7) ‘E7’ Overvoltage protection
8) ‘E8’ Controller op amp failure
9) ‘E9’ Stall protection
Wiring Port Diagram:
Power cord: big black red line
Motor wire: blue wire/green wire/yellow wire
Hall wire: red wire/yellow wire/blue wire/green wire/black wire
Tail light wire: small red wire and black wire
Software Burning line: green line/red line/black line
Communication line: green line/blue line/black line/red line/yellow line
Package Included:
Type:01
1 X:Controller
1 X:Dashboard
1 X:Accelerator
1 X:Front Light
1 X:Rear Light
1 X:Waterproof Wiring:
Type:02
1 X:Controller
1 X:Dashboard