Heater Blower Motor Fan Resistor for Fiat 500 Panda Punto Seicento Doblo Ducato

Heater Blower Motor Fan Resistor For FIAT 500/Panda Punto Seicento Doblo Ducato
Specification:
Model: 633497
Product Name:Heater/Blower Fan Resistor
Type: Heater Core
Color: As the picture shown
Material: Plastic,Metal
Terminals: 4 Pins
Interchangeable Part Numbers:
46721213
46723713
71732250
46722909
Fitments (For the reference500 MY2012 83 (2012+)
for 500L 73 (2012+)
for New/Nuova 500 3P (2007-2012)
for Barchetta PK (1995-2004)
for New/Nuova Panda 2Q (2003-2009)
for New/Nuova Panda 33 (2012+)
for Panda Classic 71 (2012-2012)
for Panda MY 2009 3U (2009-2010)
for for Panda MY 2011 0X (2010-2011)
Punto 55-60-75-90 NV (1993-1997)
for Punto BZ 1N (1999-2003)
for Punto BZ. Gamma ’97 1A (1997-1999)
for Punto for abrio PF (1994-1997)
for Punto for Cabrio Gamma’97 1C (1997-2000)
for Punto D-TD NX (1993-1997)
Punto DS 1P (1999-2003)
Punto GT NW (1993-1997)
Punto TB.DS. GAMMA’97 1B (1997-1999)
Seicento 1E (1998-2010)
Seicento Elettra 1H (1998-2003)
Stilo BZ/DS 2C (2001-2003)
Stilo F.L.L. 2003 2V (2003-200
for FIAT Professional – Doblo 1W (2000-2004)
for FIAT Professional – Doblo MY. 2004 2W (2004-2005)
for FIAT Professional – Doblo Restyle/Facelift. 2005 3C (2005+)
for FIAT Professional – Ducato Restyle/Facelift BZ/DS 2E (2001-2006)
for FIAT Professional – Ducato Russia 2008 3T (2008-2011)
Installation:
–When installed it is IMPERATIVE to monitor the temperature of the resistor on first use.
–Sometimes a blown resistor can be a symptom of the problem and not the problem itself, and replacing it in this scenario will only cause it to blow again.
–If the resistor starts heating very quickly and getting too hot IMMEDIATELY SWITCH OFF YOUR CAR and diagnose the problem elsewhere.
–Resistors usually blow when they get too hot and this happens when too much current is being drawn from then. This can happen if there is an issue with the blower motor or even the ignition system, or a fault with the wiring.
–Also please check your fan is not jamming because of dirt or grease build up, or a failure in the bearings.
–This will also cause the fan to try to draw more power in an attempt to spin, causing the resistor to overheat and fail.
–If replacing the resistor (and it is not getting hot) your heater still does not work, please check the thermo fuse or carry out further diagnosis elsewhere for a fault.
Note:
1.We provide clear pictures, measurements where possible. Please check as much as possible to make sure the item is the one that you need.
2.Please allow 0.5-1 inch difference due to manual measurement.(1inch=2.54cm)
3.There are no instructions included in this kit.Professional Installation Is Highly Recommended！
4.Please Compare The Blower Fan Resistor With Your Original One Before Purchasing！
Package Include:
1x Heater/Blower Fan Resistor